Joined in 2023 
82 
63 About this deal
No, Knauf AQUAPANEL ®Floor Tile Underlay is not approved for installation in a vertical installation. Knauf AQUAPANEL ®Joint Filler - Grey, AQUAPANEL ®Tape, AQUAPANEL ®Screws (dependent on framework type), and exterior thin render coat system (incorporating a modern thin basecoat and mesh, and a finish coat).
No, this board should only be used for internal applications. Knauf offers Knauf AQUAPANEL ®Cement Board Outdoor (which is freeze thaw tested) for exterior uses. Many of our custom projects arise from unique architectural and aesthetic design requirements that lie outside the standard parameters of typical skylights. We have worked with thousands of architects in customized frames and extrusions for specific job requirements. The large array of projects we’ve completed offers a wealth of experience and an extensive library of completed custom designs for inspiration. No, we do not recommend this as the cement is not a good conductor of heat and, due to the fixings, should not be installed directly over an insulation material either. An UFH system which is installed in the tile adhesive layer, over the board, would be OK. No, to be compliant to our installation requirements, please follow the standard installation guidance. To get more details about the LMCC’s solution, read the customer story on Microsoft Tech Community.We do not recommend directly painting as the jointing is likely to show and be unsightly. For best results, tape and joint the boards using Knauf AQUAPANEL ®Joint Filler and AQUAPANEL ®Tape. and then apply Knauf Interior Skim and apply the paint (by others) to this. Direct splash zones should always be tiled. Does the cross battened system need to be horizontal to the structure and vertical behind the Knauf AQUAPANEL ®Cement Board Outdoor?
We recommend you use a cement-based flexible tile adhesive (Class C2 / S1 according to EN 12004-12002). If you need better waterproofing than just the tiles, use a waterproof adhesive, provided it is cement based.
Gallery
No, the boards can be left without the 3 to 5mm gaps being filled for between 4 to 6 weeks before the modern thin coat basecoat, mesh and finish have to be applied to weathertight the facade. Apply the thin coat basecoat into the gaps before applying the full surface application. The Knauf AQUAPANEL ®Cement Board Outdoor, once taped and jointed, may be left exposed for up to 6 months before a render basecoat and reinforcing mesh must be applied as aminimum - this cannot be left un-rendered indefinitely and is not suitable for direct painting. The render basecoat acts to weatherproof the systemand maintain Knauf's requirements. The basecoat and reinforcing mesh may be painted without having a topcoat render applied, however in these cases, the tape and jointing process must ensure it uses the 200mm wide tape rather than the standard 100mm tape.
Knauf recommend that the boards are installed with a 3 to 5mm gap all around the boards, and all joints are taped and jointed using Knauf AQUAPANEL ®products (this must be done for soffit applications). If the thin coat render basecoat and mesh layer is going to be applied within 4 to 6 weeks of the boards being installed, the tape and jointing application can be omitted, but the basecoat must be applied into the gaps prior to application of the basecoat and mesh layer.
Privacy Statements
In case of an all-fixed skylight, please make sure to use a low E laminated safety glass, that would bring in a minimum possible amount of heat without affecting the incoming light much. This glass selection is very important because, if we select the one with a more reflective coating, the whole skylight would turn into a mirror at night and it would be a disaster. Moreover, having laminated safety glass would also take care of the safety aspects against intrusion as well as damages due to unforeseen glass breakages. Knauf AQUAPANEL ®Cement Board SkyLite can be used both as a ceiling in interior humid or wet environments where water vapour and high temperatures up to 70 °C occur, and as an exterior soffit, allowing the interior ceiling design theme to be continued through windows as a soffit under deep external roof overhang. Knauf AQUAPANEL ®Cement Board Outdoor is A1 rated to EN 13501; it is therefore non-combustible and will not allow fire to spread along its surface. However, as the board is installed over a drained and ventilated cavity, any fire may get behind the cladding. A timed fire rated walling system would be accomplished from the sheathing layer inwards. Cavity fire stopping should be discussed with the passive fire stopping specialists on the scheme. Yes, the cladding must be ventilated at the head of the cladding with a minimum gap of 10mm between the top of the rendered cladding and the structure above (soffit box, coping etc.). This allows any warm moist air to escape from the cavity. We recommend you use a cement-based flexible tile adhesive (Class C2 / S1 according to EN 12004 - 12004). If you need better waterproofing than just the tiles, use a waterproof adhesive provided it is cement based.
The benefits include easier image association with a given case, simplified new case creation, and improved data collection and accuracy. Several methods can help to decide on the size and spacing of skylights. The size of the skylight impacts its solar heat gain and its conduction gains and losses. Typically for roof windows and skylights, a 3–5 per cent floor-to-skylight area ratio is used and for some high-performing tubular skylights, 1–2 per cent is sufficient. If multiple skylights are to be used in the same room, spacing between the skylights should be 1.5 times the height of the room. Wet areas such as rooms housing swimming pools, spas and saunas, wet rooms, kitchens, laundries, bathrooms, changing rooms, domestic and commercial kitchens, restaurants or anywhere where ceramic, mosaic or stone floor coverings are specified.LMCC is an Office 365 customer and invested in PowerApps, Power Automate, Office 365 and SharePoint. Bing Maps pricing and the connectors to PowerApps and Power Automate made it the right choice. However, if we do not follow certain aspects of designing a proper skylight customised to the Indian climatic conditions, it might be a disaster and one might be living in an ‘oven’ practically. Choosing a proper design along with materials that are more suitable for local conditions is the key to incorporating a skylight into your building.
Great Deal 
New Comment