Honeywell HCW80 White Y6630D

Product Information

I have looked closely on the honeywell site and followed the instructions to bind the thermostat and reciever (I wondered if there had been a break in the RF link as I had been away) and I have replaced the thermostat batteries. I have a honeywell thermostat (HCW80) with a receiver and the boiler works fine for hot water but there is no central heating. I have reset the HC60, get into learning mode, pressed the button on the HCW80, but after a while the green light flashes on the HC60 while the red one stays on. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Keep in mind that anyone can view public collections - they may also appear in recommendations and other places. The wireless room thermostat HCW80 sends heat demand signals (RF 868,3 MHz) to the relay module HC60NG.

If I turn the stat down to its lowest setting then up to a high setting and back to its normal setting all is OK again - the green light comes on, the boiler strikes up again and all is well for an hour or so. Honeywell are the leading supplier of domestic heating and combustion controls in the UK, and are a Fortune 100 company employing over 127,000 people worldwide. Personalised advertising may be considered a “sale” or “sharing” of information under California and other state privacy laws, and you may have a right to opt out.

The Y6630D thermostat uses an anti-hysteresis software and the same receiver as you have, so yours may be the same, as it approaches the set temperature it starts to cycle off/on so it will not over shoot. The stat is normally set to 20 deg but the boiler usually switches off before the room temp has reached that.Right there should be a switched spur to the boiler which cuts power to the boiler and should also cut power to the relay which will reboot it. Honeywell Home offers smart home, home comfort, safety and energy efficiency solutions for your home. Quick question about the boiler switching off after 2mins, is this because the demand has stopped or the boiler has reached a high temperature? Later Repressing the HC60NG button the puls was different and it extinguished when pressing the HCW80 reset. Y6330D consists of a HCW80 room temperature controller and a HC60NG receiver module, the room unit HCW80 is used for intelligent room temperature control in combination with the relay module HC60NG, it can be used to control gas and oil boilers, variety of valves and actuators or electrical heating systems.

This is a stylish stand to mount the Honeywell wireless wall mounted thermostat, so you can place anywhere in the house as required without fixing in place. It can be used in conjunction with the Sundial Y or S Plan or as a stand alone device for room temperature control of a combi boiler system. NOTE: This is for the stand only and does not include the controller that is shown for demonstration purposes only.When in Teach in mode and the HCW80 test button is pressed the flashing red light on the HC60NG relay module does go out, so there is some communication between the two. com, the Sell on Etsy app, and the Etsy app, as well as the electricity that powers Etsy’s global offices and employees working remotely from home in the US. This is a rare situation, however, if this does happen our objective is to make the process as efficient and easy as possible. Does this look like a thermostat/receiver problem where i need to replace or is this a bigger problem?

p>The NOW HE0089 or HE0118 Room Stat is a direct replacement for the Y6630D and Honeywell HCW80 thermostat models. HONEYWELL SPARE ROOM STAT FOR Y6630D1007 The wireless room thermostat HCW80 sends heat demand signals (RF 868,3 MHz) to the relay module HC60NG.

Today a leading supplier to aerospace, automation, control and transportation industries throughout the world, Honeywell’s origins were in the area of heating controls, a market which they still dominate today. Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Are you 100% certain that the behaviour of each unit was *exactly* as given in the re-binding procedure in the manual? Disclaimer: Etsy assumes no responsibility for the accuracy, labelling, or content of sellers' listings and products. I did a test run of our heating a few weeks ago and all was working fine, got back from holiday yesterday and attempted to put the heating on and it's not kicking in.